PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-1.0 • LINEAR P/N: 223101X20 • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 17.500” FOLD TO 4.250” X 3.500”
• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223101X20 • IMAGE 1
DESCRIPTION
The IRE-1.0 represents the highest level in sophistication for attachable
IR Emitters. It features a unique EZ-Docker
™
port that permits instant
removal of the emitter when rearranging or servicing components.
An improved adhesive reduces callbacks for reattachment of “fallen
emitters”. The case may also be taken apart so that the tiny internal
emitter can be placed inside a component, when desired. High IR
output from the top curved surface allows emitter to be mounted
on a nearby surface, below, above or on a cabinet door, rather than
directly on the sensor of the unit where conditions permit.
ATTACHMENT
First, locate the component’s IR sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
™
port has a clear adhesive layer on its bottom surface.
Peel the protective layer off,
exposing the adhesive.
Orient the port vertical (see
Fig. 2) and press it over the
center of the component’s
sensor window. Press and
hold for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker
™
port. You should
feel it “snap” into place. (To
remove the emitter at any
time, simply push upward
until it “pops” out).
IRE-1.0
Emitter
8 FT
9/16"
7/16"
3.5mm
mini plug
1/4"
Side View
Emitter
Wire Lead
Docking
Port
Clear Adhesive Tape
(See Note 3)
Top View
NOTE: White striped
side is positive ( +
)
(–
)
(+
)
Emitter slides into
Docking Port
TYPICAL INSTALLATION
Satellite Receiver
PS-1.0
IRE-1.0
IRE-1.0
Emitter
IRE-1.0
Emitter
VCR
A/V Receiver
Hand Held
Remote
IRC-3.0
Emitter
IR Sensor
Window
AT-1.0
Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver
Fig. 1
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-1.0 shell.
Note 3: If you need to remove the EZ-Docker
™
port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Note 4: The emitter shell and EZ-Docker
™
port, though dark in
appearance, are transparent to Infrared. This allows IR commands
to pass through them, permitting local hand held remote control as
well as through the IRE-1.0.
Fig. 3
IR Controlled Components
IR sensor
window
Docking Port
IRE-1.0 attached to
IR sensor window
2) Slide IRE-1.0 Emitter
end into docking port
1) Attach IRE-1.0 Docking Port
to IR sensor window with adhesive pad
Fig. 2
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals